Login
Close

Login



SMARTen 48 Patch Panels (with Patching Switches)

 

  • Dramatically reduce the need for patch cords in normal use by integrating internal mounted Patching Switches

  • A unique innovative technology connects between each two vertical ports; Patch Cord is needed only to connect non vertical ports

  • Models for shielded or unshielded cabling systems

  • High performance panels that support Category 6A performance specifications up to 500 MHz

  • Conform to ANSI/TIA/EIA-568-C.2, ISO/IEC 11801 2nd edition and CENELEC EN50173 for Category 6A/Class EA

  • Special cap design for minimizing Alien Cross-Talk

  • Simple labor-saving termination using standard 110 & Krone termination tools

  • Backward compatible with Category 5e and Category 6 cabling standards

  • Compatible with 22-26 AWG Solid or stranded wire cables

  • High durability and reliability

 

 

 

SMARTen
RiT SMARTenTM STP Patch Panels are part of the RiT SMARTen CablingSystemTM, featuring Category 6A performance. The system is designed to ANSI/TIA/EIA-568-B.2-10 latest draft, ISO/IEC 11801 2.1 edition and CENELEC EN50173 (200x) for Category 6A/CLASSEA. The system is designed to support protocols running at up to IEEE 802.3an 10Gbps, 1000 Mbps, such as ATM 622 Mbps and Gigabit Ethernet.

 

PatchView Capability
Special SMARTen STP 24 Patch Panels models, when used in conjunction with RiT's PatchViewTM Solution, are able to provide valuable connectivity information about the entire network to the PV4E management software. LED indicators on panels identify any two ports patched together and enable 100% accurate Moves, Adds and Changes (MACs). With its unique automated detection, LED-guided connection, and web-based remote maintenance capabilities, PV4E enables real-time, centralized management and troubleshooting for even the most dispersed networks.

RiT SMARTen 48 Patch Panels offer an innovative high quality patching solution that is made to last. Each two vertical ports are connected to each other unless a patch cord is mounted into one of the ports.This robust system significantly reduces the need for patch cords while exceeding all Category 6A performance requirements.  

The SMARTen 48 Patch Panel conform to ANSI/TIA/EIA-568-C.2, ISO/IEC 11801 2nd edition and CENELEC EN50173 (200X) for Category 6A/Class EA. The system is designed to support protocols running at up to IEEE 802.3an 10Gbps, 1000 Mbps, such as ATM 622 Mbps and Gigabit Ethernet and future high-speed applications. 

The panels are optimized for ease of assembly and termination. With simple labor-saving termination using standard 110 & Krone Block termination tools and color-coded wiring blocks, installation costs are significantly reduced.

By using RiT’s special cap design for minimizing Alien Cross-Talk the panel exceeds the crucial parameter for 10G application – Alien Cross-Talk. 

Special SMARTen UTP models, when used in conjunction with RiT's PatchView system, are able to perform remote or on-site scanning of the patching configuration. The entire wiring center's patching configuration is continuously monitored by a Scanner which reports the data to a remote terminal. The network administrator uses this data as a vital part of his cabling management system. The data may be displayed on the panel itself by LED indicators. 

 

Interface

  • Front Interconnection (patch cord side)  
    48 eight-position or nine-position RJ-45 shielded or unshielded modular jacks.

  • Back Interconnection (cabling side)
    48 eight-position
    110 & Krone tool-compatible blocks; accept 22 to 26 AWG wires, solid or stranded. Rated for up to a minimum of 200 re-termination cycles.

    Note: Termination tools must be ordered separately.

  • Interconnection to RiT's PatchView system
    • PVMax Panels - Two 14-pin headers on the back of the panel are used for connection to the PVMax Scanner. Use one Group B Scanner Attachment Cord according to the required length

    • The scanning signal is transmitted over pin 9 of the RJ-45. Pin 9 exists in nine-position RJ-45 jack and plug designs, used for these patch panel models. A special patch cord -SMART Jumper, including an extra wire and special RJ-45 plugs is needed. Please refer to the PatchView System and the Copper Cables and Cords sections

  • Indicators (in models adapted to PatchView only)
    Port identification indicators - 48 red LEDs. A pair of activated LEDs identifies connected ports. A single port can be identified and the corresponding LED activated by a remote control command from the network management station.

  • Patching Switches
    24 Patching Switches for internal inside patching. When patch cord is not inserted – each two upper and lower ports are connected. When patch cord is inserted - upper and lower ports are disconnected. Eight wires and the ninth scanning wire of each port are simultaneously switched.

Electrical Specifications

Category 6 / CLASS E

 

  Number   Description
 R3244000  SMARTen UTP Panel, 48, Switches
 R3244004  SMARTen UTP Panel, 48, Switches, PVMax
 R3244010  SMARTen STP Panel, 48, Switches
 R3244014  SMARTen STP Panel, 48, Switches, PVMax

 


Contact Us

 

About RiT Cabling Solutions

 

Copper Patch Panel Components:

Copper Frames 

SMARTen (CAT 6A) 

CLASSix (CAT 6) 

Giga (CAT 5e) 

Additional Components 

 

RiT Fiber Cabling

 

 

Please fill in your details and our staff will contact you.
*
*
*
*
*
*
*Required
*Enter the below security code here

Refresh
Close